Turn-Over Table for Double-Wall production A8290

1 used Turn-Over Table

for Double-Wall production
Manufacturer: SCHWINGHAMMER
Steel covering even for faced concrete
Dimensions per table: 12,50 x 3,50m
Wall thicknesses: 20 – 40 cm
Incl. 2 x 8 pieces vibrators
Incl. hydraulic cylinders
Hydraulic 7.5 kW, 150 l. Tank, 200 bar
Heating pipes for water are installed

Technical specifications:
Usable length: 12.5 m
Usable width: 3.50 m
Height: approx. 1 m
Payload tilting table 750 kg / sqm
Payload Turn-Over Table 400 kg / sqm from 80 ° to 180 °
Tilt angle: approx. 80 ° or 180 °
Operating pressure: 180 bar
Electric connection hydraulics: 15 kW
Net weight: tilting table 11tons, folding table 13tons

Turn-Over Table

Turn-Over Table

Request for more Information: please use this form Continue reading

Mesh-Welding Line EVG GE12/102-LTPV A8282

Mesh-Welding Line EVG GE12/102-LTPV

Year of construction 2009

Output: 110 Weldingcycles per minute (equal to 110 Transversal bars per minute)

Max. shape of the produced wire mesh: 2.40m x 7.80m

Long bars and transversal bars are fed by prepared bars

Straightening and Cutting of the bars is done by 2 EVG Cutting lines which work from coil

On demand there is a Cold Rolling Line with 2 blocks available which is suits to the capacity of the mesh welding line.

Mesh-Welding Line

Mesh-Welding Line

Request for more Information: please use this form Continue reading

Floor T-Beam Moulds 12pcs A8281

Floor T-Beam Moulds

Year of construction: 2007 (very little use)
Manufacturer: Macfab
150mm deep, 127mm wide
The set is self stressing 12 beams wide and consists
of 12 number 6.0m beds including the ends with safety barriers

Features:
Self Stressing unit no need for buried anchored ends.
Modular sections means bed lenght can vary.
Superior finish.
Special concrete cutting equipment is not needed.
A budget solution for pre-stressed flooring.
Size of beams give easy access and lifting onsite.

Floor T-Beam Moulds

Floor T-Beam Moulds

Request for more Information: please use this form Continue reading

1 used Twin column mould NUSPL A8279

1 used Twin column mould

Brand: NUSPL type Duplex
Very well-maintained condition!

Total length: 21m
Segment lengths 12m + 9m

Max. Production height: 1.200mm
Max. Production width: both sides 800mm each

Incl. central hydro pump unit
With built-on electrical control
Plant set up for joint operation
or the division into segments 12 and 9m

1 casting compartment Betoplan planked
1 casting compartment with complete steel covering

Includes 14 pcs High frequency vibrators, BOSCH
The electric connection for the vibrators
is 250 V / 200 Hz, frequency 6000 rpm

Twin column mould

Twin column mould

Request for more Information: please use this form Continue reading

Wire Straightening line EVG-FILZMOSER RA-XE 16/8-2 A8270

Used Wire Straightening line with hyperbolic rotors EVG-FILZMOSER RA-XE

Brand/Type: EVG RA-XE 16 / 8-2
Year 2005
Specified for double wire / double feed
up to 16 mm (80% more power)
(currently with coils up to 14 mm)

Included:
Run-off table 14 m, for double wire
Pay-offs electrical driven / braked CG 3000
8 pcs. Wire pay-offs, 3 to
Wire coil changing during production
2 pcs. shears for flying cut
Bar collection device 14m
Control console stationary

Straightening line

Straightening line

Request for more Information: please use this form Continue reading

1 used Column Formwork A8265

1 used Column Formwork

Year of construction 2008
The formwork was barely used!
Support from base: 800 x 40 x 60 cm
Transition to the rejuvenation: L = 20 cm
Rejuvenated part: 500 x 24 x 60 cm
Base: 200 x 290 x 50 cm

Support: One longitudinal side formwork height (60cm) rigidly connected to the ground,
one longitudinal side hinged.
No external vibrators installed, since it was compacted by means of a vibrating bottle.
Weight: 4.5 t

Column Formwork

Column Formwork

Request for more Information: please use this form Continue reading

Stirrup Bender MEP Mini Syntax A8266

Stirrup Bender MEP Mini Syntax

7 braked pay-offs, 7 coil holders
pulling winch, MEP auto-diameter change, 12 m collection rack, safety fences

full set of spare parts,
opt to buy an automatic portable wire straightener,
accessory for producing circle stirrups
VERY GOOD condition although 2001 and very low operating hours

Single Strand Processing Wire Diameter Φ6mm-Φ16mm
fy=600N/mm2, ft=700N/mm2
Double Strand Processing Wire Diameter Φ6mm-Φ12mm
fy=600N/mm2, ft=700N/mm2
Square Stirrup Dimensions
Minimum with Φ6mm wire – #2wire (optional bending pin) 80mm x 80mm
Maximum if clockwise 1.500mm x 1.500mm
Maximum if counter clockwise 2.000mm x 2.000mm
Length of Straightened & Cut-to-Length Bars
Minimum 5mm
Maximum (with the existing support guide-collection bench/rack) 12.000mm

Stirrup Bender MEP Mini Syntax

Stirrup Bender MEP Mini Syntax

Request for more Information: please use this form Continue reading

Precast Hollow Core Floor Production System COOTE A8264

Precast Hollow Core Floor Production System

Complete Dry Cast production system includes:
– Feed Hopper
– Mould
– Mould/Core Carrier
– Pallet Transfer Conveyor
– Mould Spray Unit
– Pallet Handler and much more

Detailed Specification:
CASTING MODULE
• Mould area: 7.0 meters long x 0.600 meters wide
• Product height: 150mm
• Product weight: 1400 kg.(max)

Precast Hollow Core Floor Production System

Precast Hollow Core Floor Production System

Request for more Information: please use this form Continue reading

Carousel Line for Floor Panels Production WECKENMANN A17179

Carousel Line for Floor Panels Production

Brands: WECKENMANN, VOLLERT, NUSPL, FILZMOSER, NETTER, UNITECHNIK, SAA

with 43 pcs moving steel moulds

Dimension of each mould: Length 16.30m, Width: 2.40m

Including:
Demoulding crane, Moulds stacking crane, Plotter and Double cleaning system, Shuttering-transport and cleaning, Oiling system, Concrete Distributor, Vibration: Gyroshake, Full Automatic Reinforcement Center FILZMOSER, Lattice girder preparation with Magnets-Handling,  Steel straightening and cutting machine 5 Lines, Wire Diameters: 6 – 14mm for Longitudinal bars and cross bars with spacers and much more.

Carousel Line

Carousel Line

Request for more Information: please use this form Continue reading

Used B&R Controls in E-cabinets A8258

Used B&R Controls in E-cabinets

Used B+R Controls, E-Cabinet consist of 3pcs Cabinets with
different modules of B&R Control racks and
Hauser Converters and others
according pictures.
B+R Provit Terminal
Various B+R Controls
Different electronic cards:
NT44, CP70, PP60, PNC3, MARC, EXS2, EXE3, E243, A, PNC8
Hauser Servax Converter

B&R Controls in E-cabinets

B&R Controls in E-cabinets

Request for more Information: please use this form Continue reading

43 Casting Tables (Pallets) for Floor Slabs NUSPL A8248

Casting Tables for Floor Slabs

Dimension/Casting Area: 15.50 x 2.40m
Could be used for mobile production (as a moving pallet) or as fixed tables
Used to produce faced concrete floor slabs

Includes complete transport/carousel equipment from VOLLERT
consisting of:
1 pc VOLLERT/NETTER compacting unit with 4 vibrators
2 pc lateral moving carts
55 pcs single transport rolls, height 500mm
21 pcs drive rolls, including control units
40 pcs terminal switches
including control, Alarm and Security equipment

Casting Tables for Floor Slabs

Casting Tables for Floor Slabs

Request for more Information: please use this form Continue reading

Plotter AVERMANN A8242

Plotter AVERMANN – FOR SALE

Year: 2012
Condition: almost new, very good
CONTROL: IPC and E-cabinett
Moving area: max: 8500mm x 3600mm
Clear height: 2868mm

The plotter marks slabs cutting lines, rectangles and circles for openings and recesses, texts for identification on cast slab surface or places for dividers and fittings on empty bed surface.

Plotter AVERMANN

Plotter AVERMANN

Request for more Information: please use this form Continue reading

Turn-Over Table 2pcs for Double-Wall production SOMMER A8240

2 pcs used Turn-Over Tables for Double-Wall production

Brand: SOMMER
Year 2007, less used
Casting area: 7215 x 3140mm
Max. element size: 7100 x 3000mm
Max. Load: 11tons
Double-Wall Thickness: 180-400mm
Steel sheet 8mm, even face
Used for face concrete
Including:
E-Vibration
Converter
Control

Turn-Over Tables for Double-Wall production

Turn-Over Tables for Double-Wall production

Request for more Information: please use this form Continue reading

Lean Production Concepts for your Precast Plant

Precast-plants, machines, precastplants

GMS offers complete solutions of Precast factories and single production machines for Precast products. GMS has the solution, whether you are adapting an existing production line or invest in a Start-up Precast plant. GMS can offer you used or new Machinery and Precast plant systems and has the ability to design, engineer and install complete precast production plants.

The newest development is the „Lean Precast Carousel“. A low cost solution, which can be extended in further steps.

by Franz Filzmoser

 

Schlanke Fertigung von Betonfertigteilen

Lean-Precast-Carousel

Request for more Information: please use this form Continue reading

Concrete Spreader 2m³ EBAWE 2008 A8232

Concrete Spreader EBAWE

Year of construction 07/2008, 2 m³ content
discharge width 1.25 m with 14 slide valves,
all individually switchable via buttons and footswitch.

Longitudinal and lateral ride via joystick steplessly adjustable,
movable on drilled steel profiles.

Concrete spreader is used for a table
length of 12.50 m and width of 2.50 m
Total length travel 20 m. (cable drum
)

Concrete Spreader

Concrete Spreader

Request for more Information: please use this form Continue reading

GMS-Formwork START-PACKAGE

GMS-Formwork START-PACKAGE

The GMS-Formwork START-PACKAGE enables Precast Products Manufacturers to try out the newest developments in Precast Formwork Systems. The Spartan Sideforms and Titan Magnets are developed to produce concrete panels in any desired size. In a very short time and with the lowest possible efforts.

MOST IMPORTANT FEATURES:
– the flexibility of different heights from 100 to 325mm
– lightweight Aluminium, easy to handle
– very stable together with the strong magnets
– sealing in the bottom, no leak outs of concrete
– fast and easy Assembling
– easy Cleaning, with water and brush

The GMS-START-PACKAGE enables the precaster to cast various precast panel sizes in one operation. The panel size could have 30m2.

The START-PACKAGE includes

– 5pcs Spartan side forms each length of 5.80m
-18pcs Titan Magnets, which could be used for other formwork systems as well, if you fix Ball Lock Rail Strips to the  other formwork planks, boards etc.  Will be delivered in Nylon or steel depending on the kind of the planks material

GMS-Formwork START-PACKAGE

REQUEST FOR QUOTATION: please use this form Continue reading

Lattice girder welding Line EVG-FIL GH300 A17172

EVG/FIL GH300 – FOR SALE

Year 1995,
Lattice girder height 70 – 300mm
Wires: 5-14mm
1 pc main body with bending , welding and cutting
1 pc Electric Cabinet with Control-Unit: B&R
1 pc hydraulic unit with water recooler
5 pcs wire pay-offs and wire straightening devices
1 pc girder run-off and stacking system


Lattice girder welding Line

Lattice girder welding Line

Request for more Information: please use this form

Battery Mold TECHNOPLAN A16157

Battery Mold TECHNOPLAN – FOR SALE

17 Compartments, thereof
9 Compartments measure 9.00 x 2.80m
8 Compartments measure 6.50 x 2.80m

– Frequency controlled Vibration from WACKER
– including formwork equipment for doors and windows

Year: 1998, not much used!
IN A VERY GOOD CONDITION

 

Battery Mold

Battery Mold

Request for more Information: please use this form Continue reading

Reinforcement Cage Assemblers A17199-A17200

Used Reinforcement Cage Assemblers FOR SALE

We sell 1 SCHNELL IDEA and 1 MEP Preform

Using three thin longitudinal wires, which may be welded to any point of the stirrup’s exterior surface. IDEA is able to half-assemble lattice girders of stirrups of any shape and size.

The half-assembled girder is now ready to be finished off by fixing the frame carrying bars. As the stirrups have already been welded at the correct distance, the carrying bars may be only tied every 5 or 6 stirrups.

This means:
– saving up to 60% on assembling costs;
– maximum flexibility: girders may be assembled with stirrups of any shape and size; besides this system avoids all size restrictions and material waste involved with the use of electrowelded mesh;

Cage Assemblers

Cage Assemblers

Request for more Information: please use this form Continue reading

Hyperbolic Rotor-Straightener RA-X EVG-FILZMOSER A16158

Hyperbolic Rotor-Straightener – FOR SALE

Very smooth surface of the straightened wire bars
Use of wire coils, diameters 6 to 14mm
6 unwinding reels 6-14mm, alternatively 2×10 oder 12mm.
Production of straightened bars and
2 Bending units
Bar distribution conveyor
Chain conveyor with 100mm sections
Can be inspected during operation.

 

Hyperbolic Rotor-Straightener

Hyperbolic Rotor-Straightener

Request for more Information: please use this form Continue reading

Wire cage welding machine A15079

Round wire cages with sockets  – FOR SALE

Cage diameter 320-1600mm for precast concrete pipes
with sockets
Brand: HK-Technik
Production process: continuously
Length of cage: on demand
Line wire diameter: 6mm
Winding wire diameter: 5-8mm
Number of line wires: 12pcs
Rise of winding wire: 30-150mm

 

Wire cage welding machine

Wire cage welding machine

Request for more Information: please use this form Continue reading

Curved staircase formwork HOWAL ALPHATOP – A15090

Variable staircase formwork for curved staircases

Many different shapes in the riser range from 17.0 to 19.0 cm. Flight of stairs in clockwise and counterclockwise design. Step width is 100 cm, step depth is 26 cm.

Minimal adjustment and setup times, this enables daily casting. High quality elements, fair-faced concrete in the underside.

 

Curved staircase formwork

Curved staircase formwork

Request for more Information: please use this form Continue reading

New Precast Concrete Formwork

Prior Notice to Precasters

Introduction of a new formwork system by GMS to the precast concrete market.

The Sideform
is manufactured of ultra lightweight Aluminum. Not only can you change the hight of the sideform, but also you can have either a chamfer edge profile or a square one simply by changing the capping on the side form. A rubber base insert provides a silicon-free seal between bed and formwork to prevent concrete bleed.

Ergonomic and strong Magnets
simple and safe operation. Easy cleaning and maintenance. Flexibility to use not only our Aluminum Sideforms but also all other sideforms by using adaptors.

www.precastplants.com is a Domain of GMS
GMS-Abschaler

precast concrete formwork

Request for more Information: please use this form Continue reading

MEP Wire Girder Welding Line MTM400 A17164

LATTICE GIRDER PRODUCTION

Output max.: 33 m/min
Lattice girder height: 80-300 mm (easily variable; precise motorized vertical regulation)
L.G. base (internal size) : 70-100 mm
Advance step:   400 mm
Lattice girder length: 2000-12000 mm (multiples of 100 mm)

DIAMETER OF THE WIRE:
Longitudinal wire Ø: 5-12 mm
Continuous stirrup (zigzag) Ø: 3.5-6 mm
(fy = 650 N/mm2 – ft = 650 N/mm2)

2009: Comprehensive update of the entire electrics/electronics
2014: Comprehensive update of the entire mechanic systems, repainting. Now it looks as if it was new!

Wire Girder Welding Line

Wire Girder Welding Line

Request for more Information: please use this form Continue reading

How much for my Precast Plant ?

How much can I get for my precast production plant or equipment?

To find out the worth of your production machine/plant send some basic information like:

  • Brand/Type of the machine/ equipment/ plant
  • Year/ Capacity
  • Condition and add. info i.e. photos

Send us an e-mail to moc.s1542329871tnalp1542329871tsace1542329871rp@of1542329871ni1542329871 or use the Request Form below:

Wieviel bekomme ich für meine gebrauchte Maschine?

How much can I get for my used machine ?

Request for more Information: please use this form Continue reading

Wall-Elements Plant for lightweight concrete panels A14053

Lightweight concrete panels production plant – FOR SALE

For panels, slabs, walls made in LIAPOR, LECA or other light materials to encase or insulate warehouses, distribution centres and industrial buildings with steel frame construction.
Further the equipment can be adapted for the production of standard concrete walls and floors as well.

Pallets Carousel Line, Pallets dimension/max. element size: 2.00 x 12.00 m

Complete Concrete Mixing plant with cement silos, aggregates silos, conveyor belts, bucket elevator etc. is included.

Precast concrete panels are delivered to site made to measure. Manufactured in controlled environment factory conditions, the panels are quickly erected to provide high quality precast concrete walls.

Wall-Elements Plant

Wall-Elements Plant

Request for more Information: please use this form Continue reading

Lattice girder welder PROGRESS A15084 + BARGAIN +

Lattice girder resistance welder PROGRESS – FOR SALE

Year 2012
380V/50Hz
Consists of body with welder, transformer, welding control unit and foot-switch.
Semi-manual operation
Type of lattice girder: KT 800
Girder height: 90-320mm
Max. diameter to weld: 12mm

THIS PRODUCT IS CATEGORIZED AS A BARGAIN AND ITS PRICE BELOW
EUR 10000

 

Gitterträger Schweissmaschine

Lattice girder resistance welder PROGRESS

Request for more Information: please use this form Continue reading

Precast moulds for System Tanks A16141

System Tank Moulds – FOR SALE

Precast Concrete Moulds to produce System Tanks from 100 m3 –  7000 m3.

These tanks can be used as sedimentation tanks, digestion tanks, aeration tanks, storm water retention basins, elevated reservoirs, clarifiers, filtration tanks, sprinkler tanks, firefighting tanks, flammable or environmentally dangerous liquids safety tanks, loose storage tanks (salt, sand, chipping, etc), agricultural application tanks and rain water harvesting tanks.

 

Sytem-tank-molds

System-tank-moulds

Request for more Information: please use this form Continue reading

EBAWE precast concrete form plotter A14054

Universal plotter – FOR SALE

Year: 2013
Condition: almost new, very good
Steuerung: PC und Steuerschrank
Moving area: max: 12975mm x 3813mm

The plotter marks slabs cutting lines, rectangles and circles for openings and recesses, texts for identification on cast slab surface or places for dividers and fittings on empty bed surface.

plotter

EBAWE plotter

Request for more Information: please use this form Continue reading