Turn-Over Table for Double-Wall production A8290

1 used Turn-Over Table

for Double-Wall production
Manufacturer: SCHWINGHAMMER
Steel covering even for faced concrete
Dimensions per table: 12,50 x 3,50m
Wall thicknesses: 20 – 40 cm
Incl. 2 x 8 pieces vibrators
Incl. hydraulic cylinders
Hydraulic 7.5 kW, 150 l. Tank, 200 bar
Heating pipes for water are installed

Technical specifications:
Usable length: 12.5 m
Usable width: 3.50 m
Height: approx. 1 m
Payload tilting table 750 kg / sqm
Payload Turn-Over Table 400 kg / sqm from 80 ° to 180 °
Tilt angle: approx. 80 ° or 180 °
Operating pressure: 180 bar
Electric connection hydraulics: 15 kW
Net weight: tilting table 11tons, folding table 13tons

Turn-Over Table

Turn-Over Table

Request for more Information: please use this form Continue reading

Mesh-Welding Line EVG GE12/102-LTPV A8282

Mesh-Welding Line EVG GE12/102-LTPV

Year of construction 2009

Output: 110 Weldingcycles per minute (equal to 110 Transversal bars per minute)

Max. shape of the produced wire mesh: 2.40m x 7.80m

Long bars and transversal bars are fed by prepared bars

Straightening and Cutting of the bars is done by 2 EVG Cutting lines which work from coil

On demand there is a Cold Rolling Line with 2 blocks available which is suits to the capacity of the mesh welding line.

Mesh-Welding Line

Mesh-Welding Line

Request for more Information: please use this form Continue reading

Floor T-Beam Moulds 12pcs A8281

Floor T-Beam Moulds

Year of construction: 2007 (very little use)
Manufacturer: Macfab
150mm deep, 127mm wide
The set is self stressing 12 beams wide and consists
of 12 number 6.0m beds including the ends with safety barriers

Features:
Self Stressing unit no need for buried anchored ends.
Modular sections means bed lenght can vary.
Superior finish.
Special concrete cutting equipment is not needed.
A budget solution for pre-stressed flooring.
Size of beams give easy access and lifting onsite.

Floor T-Beam Moulds

Floor T-Beam Moulds

Request for more Information: please use this form Continue reading

1 used Twin column mould NUSPL A8279

1 used Twin column mould

Brand: NUSPL type Duplex
Very well-maintained condition!

Total length: 21m
Segment lengths 12m + 9m

Max. Production height: 1.200mm
Max. Production width: both sides 800mm each

Incl. central hydro pump unit
With built-on electrical control
Plant set up for joint operation
or the division into segments 12 and 9m

1 casting compartment Betoplan planked
1 casting compartment with complete steel covering

Includes 14 pcs High frequency vibrators, BOSCH
The electric connection for the vibrators
is 250 V / 200 Hz, frequency 6000 rpm

Twin column mould

Twin column mould

Request for more Information: please use this form Continue reading

Wire Straightening line EVG-FILZMOSER RA-XE 16/8-2 A8270

Used Wire Straightening line with hyperbolic rotors EVG-FILZMOSER RA-XE

Brand/Type: EVG RA-XE 16 / 8-2
Year 2005
Specified for double wire / double feed
up to 16 mm (80% more power)
(currently with coils up to 14 mm)

Included:
Run-off table 14 m, for double wire
Pay-offs electrical driven / braked CG 3000
8 pcs. Wire pay-offs, 3 to
Wire coil changing during production
2 pcs. shears for flying cut
Bar collection device 14m
Control console stationary

Straightening line

Straightening line

Request for more Information: please use this form Continue reading

1 used Column Formwork A8265

1 used Column Formwork

Year of construction 2008
The formwork was barely used!
Support from base: 800 x 40 x 60 cm
Transition to the rejuvenation: L = 20 cm
Rejuvenated part: 500 x 24 x 60 cm
Base: 200 x 290 x 50 cm

Support: One longitudinal side formwork height (60cm) rigidly connected to the ground,
one longitudinal side hinged.
No external vibrators installed, since it was compacted by means of a vibrating bottle.
Weight: 4.5 t

Column Formwork

Column Formwork

Request for more Information: please use this form Continue reading

Stirrup Bender MEP Mini Syntax A8266

Stirrup Bender MEP Mini Syntax

7 braked pay-offs, 7 coil holders
pulling winch, MEP auto-diameter change, 12 m collection rack, safety fences

full set of spare parts,
opt to buy an automatic portable wire straightener,
accessory for producing circle stirrups
VERY GOOD condition although 2001 and very low operating hours

Single Strand Processing Wire Diameter Φ6mm-Φ16mm
fy=600N/mm2, ft=700N/mm2
Double Strand Processing Wire Diameter Φ6mm-Φ12mm
fy=600N/mm2, ft=700N/mm2
Square Stirrup Dimensions
Minimum with Φ6mm wire – #2wire (optional bending pin) 80mm x 80mm
Maximum if clockwise 1.500mm x 1.500mm
Maximum if counter clockwise 2.000mm x 2.000mm
Length of Straightened & Cut-to-Length Bars
Minimum 5mm
Maximum (with the existing support guide-collection bench/rack) 12.000mm

Stirrup Bender MEP Mini Syntax

Stirrup Bender MEP Mini Syntax

Request for more Information: please use this form Continue reading

Precast Hollow Core Floor Production System COOTE A8264

Precast Hollow Core Floor Production System

Complete Dry Cast production system includes:
– Feed Hopper
– Mould
– Mould/Core Carrier
– Pallet Transfer Conveyor
– Mould Spray Unit
– Pallet Handler and much more

Detailed Specification:
CASTING MODULE
• Mould area: 7.0 meters long x 0.600 meters wide
• Product height: 150mm
• Product weight: 1400 kg.(max)

Precast Hollow Core Floor Production System

Precast Hollow Core Floor Production System

Request for more Information: please use this form Continue reading

Carousel Line for Floor Panels Production WECKENMANN A17179

Carousel Line for Floor Panels Production

Brands: WECKENMANN, VOLLERT, NUSPL, FILZMOSER, NETTER, UNITECHNIK, SAA

with 43 pcs moving steel moulds

Dimension of each mould: Length 16.30m, Width: 2.40m

Including:
Demoulding crane, Moulds stacking crane, Plotter and Double cleaning system, Shuttering-transport and cleaning, Oiling system, Concrete Distributor, Vibration: Gyroshake, Full Automatic Reinforcement Center FILZMOSER, Lattice girder preparation with Magnets-Handling,  Steel straightening and cutting machine 5 Lines, Wire Diameters: 6 – 14mm for Longitudinal bars and cross bars with spacers and much more.

Carousel Line

Carousel Line

Request for more Information: please use this form Continue reading

Used B&R Controls in E-cabinets A8258

Used B&R Controls in E-cabinets

Used B+R Controls, E-Cabinet consist of 3pcs Cabinets with
different modules of B&R Control racks and
Hauser Converters and others
according pictures.
B+R Provit Terminal
Various B+R Controls
Different electronic cards:
NT44, CP70, PP60, PNC3, MARC, EXS2, EXE3, E243, A, PNC8
Hauser Servax Converter

B&R Controls in E-cabinets

B&R Controls in E-cabinets

Request for more Information: please use this form Continue reading

43 Casting Tables (Pallets) for Floor Slabs NUSPL A8248

Casting Tables for Floor Slabs

Dimension/Casting Area: 15.50 x 2.40m
Could be used for mobile production (as a moving pallet) or as fixed tables
Used to produce faced concrete floor slabs

Includes complete transport/carousel equipment from VOLLERT
consisting of:
1 pc VOLLERT/NETTER compacting unit with 4 vibrators
2 pc lateral moving carts
55 pcs single transport rolls, height 500mm
21 pcs drive rolls, including control units
40 pcs terminal switches
including control, Alarm and Security equipment

Casting Tables for Floor Slabs

Casting Tables for Floor Slabs

Request for more Information: please use this form Continue reading

Plotter AVERMANN A8242

Plotter AVERMANN – FOR SALE

Year: 2012
Condition: almost new, very good
CONTROL: IPC and E-cabinett
Moving area: max: 8500mm x 3600mm
Clear height: 2868mm

The plotter marks slabs cutting lines, rectangles and circles for openings and recesses, texts for identification on cast slab surface or places for dividers and fittings on empty bed surface.

Plotter AVERMANN

Plotter AVERMANN

Request for more Information: please use this form Continue reading

Turn-Over Table 2pcs for Double-Wall production SOMMER A8240

2 pcs used Turn-Over Tables for Double-Wall production

Brand: SOMMER
Year 2007, less used
Casting area: 7215 x 3140mm
Max. element size: 7100 x 3000mm
Max. Load: 11tons
Double-Wall Thickness: 180-400mm
Steel sheet 8mm, even face
Used for face concrete
Including:
E-Vibration
Converter
Control

Turn-Over Tables for Double-Wall production

Turn-Over Tables for Double-Wall production

Request for more Information: please use this form Continue reading

Concrete Spreader 2m³ EBAWE 2008 A8232

Concrete Spreader EBAWE

Year of construction 07/2008, 2 m³ content
discharge width 1.25 m with 14 slide valves,
all individually switchable via buttons and footswitch.

Longitudinal and lateral ride via joystick steplessly adjustable,
movable on drilled steel profiles.

Concrete spreader is used for a table
length of 12.50 m and width of 2.50 m
Total length travel 20 m. (cable drum
)

Concrete Spreader

Concrete Spreader

Request for more Information: please use this form Continue reading

Battery Mold 3.0m x 6.5m A8254 **SOLD**

1 used Battery Mold

Face sheets are flat and even
The formwork is complete and functional!

Technical specifications:
4 pouring compartments, size: 3000mm x 6500mm (HxB)
1 fixed outer wall, thickness 780mm
3 movable partitions on rails, thickness 220mm
1 movable outer wall, thickness 780mm on rails
Incl. Work platform, stairs and railings
including 17 pieces built-in BOSCH external vibrator and
1 piece BOSCH frequency converter 1 controller
1 hydraulic unit to close the battery mold
1 built-in heating register in outer and movable partitions

Battery Mold

Battery Mold

Request for more Information: please use this form Continue reading

Progress MSR 16/5-2 BK/e VA for Precasters A8273 **SOLD**

Progress Straightening Machine MSR 16/5 – 2BK/e VA

to produce straight bars from coil and bended
wires Especially suitable for Precasters,
produced wire bars will be delivered automatically
down to the casting table
Year: 1995
Serial No: 9400065
Output: max. 116m/min
400 V/ 50 – 60 Hz
Power: 55kW
Noice Level: <85dB(A)
Included: 5 pay-offs and Run-off table and 2 Bending units

Straightening Machine

Straightening Machine

Request for more Information: please use this form Continue reading

Tilting table 22.50m x 3.00m A8277 **SOLD**

SKAKO Tilting table 22.50m x 3.00m

Outer width 3.10m
5 Hydrocylinders including Hydraulic-station
On both sides hydraulically movable side forms. These side forms limit the width to 2.72m. If the side forms are removed 3m are available for casting.
Weight: 22tons
Manufacturer: SKAKO Year 1995
Not used very much. The factory was closed for 15 years.
2pcs are available

Tilting table 22.50m x 3.00m

Tilting table 22.50m x 3.00m

Request for more Information: please use this form Continue reading

Lattice Girder Welding Line AWM 2006 Variable Pitch A7224 **SOLD**

Lattice Girder Welding Line

Year 2006
Diameter of upper wire: 6 – 14 mm
Diameter of lower wires:  6 – 14 mm
Diameter of cross-wise wires: 5 to 6 mm
Pitch/spacing of cross-wires: from 190 to 210mm
Height of the truss: from 100 to 300 mm
Pitch: 400 mm

Operation frequency  – from 35 to 70 cycles per minute.

Request for more Information: please use this form

Lattice Girder Welding Line

Lattice Girder Welding Line

Automatic Bending Machine SCHNELL EURA 16 DUAL A8236 **SOLD**

Automatic Bending Machine from Coil

Year: 2005

Eura 16 Dual is a dual-direction bender, with 2 bending heads, apt to manufacture stirrups and rebars with bends at both ends processing both hot and cold-drawn steel in coils, using wires of up to Ø 16 mm or double Ø 12 mm.

Single strand up to: 6 ÷ 16 mm #2 ÷ #5
Double strand up to: 6 ÷ 12,7 mm #2 ÷ #4
Central mandrels Ø: 20 ÷ 100 mm 3/4″ ÷ 4″
Max pulling speed: 108 m/min 354 ft/min

Included: 3 wire pay-offs

SCHNELL EURA 16 DUAL

SCHNELL EURA 16 DUAL

Request for more Information: please use this form Continue reading

Box Culvert Molds A8246 **SOLD**

2pcs Box Culvert Molds

Manufacturer: EBAWE
They come together with all the necessary equipment to produce Box Culverts.
Each Mold can be equipped with 2 cores.
Includes all necessary formwork and accesories.

Mold #8 and #9
Lay-out space: 11.5 x 7.0m each
Max. product dimensions: Height 3000mm, Length 3000mm, Width 8000mm
Including Hydraulic Station.

Box Culvert Molds

Box Culvert Molds

Request for more Information: please use this form Continue reading